IMETCO SHOP DRAWING REQUEST FORM

STEP 1: This form is required to schedule shop drawings and must be completely filled out. (Indicate N/A if Not Applicable)

STEP 2: Mail all supporting information that cannot be emailed or faxed. All information must be received to prevent delaying start of shop drawings. Scheduling Confirmation notices will be emailed to the Sales Representative.

Information required to process request: 
- This form filled out with complete information
- Architectural Drawings marked with included areas
- Specifications
- Wind Uplift & Snow Load results calculated for this project
- Photo’s of existing buildings for retro-fit projects
- Tax Exemption Certificate (if applicable)
Project Setup









Project Information
Please describe the general scope of the project.  Define any areas of the plans that are not to be included.

 






 

 
Customer Service Information













Product Selections



ZIP-RIB






Please define the pattern with Hole Size, Spacing (centers), Staggered (most common) or Straight, and Percent Open.
Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.








Batten-Tite

Straight panels are available in custom widths from 10" to 34.5"





Please define the pattern with Hole Size, Spacing (centers), Staggered (most common) or Straight, and Percent Open.
Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.








Series 300






Please define the pattern with Hole Size, Spacing (centers), Staggered (most common) or Straight, and Percent Open.
Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.








TwinLok





Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.







PermLok






Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.





SS Panel



Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.




7.2 Rib





Please define the pattern with Hole Size, Spacing (centers), Staggered (most common) or Straight, and Percent Open.
Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.




Cor-Pan







Please define the pattern with Hole Size, Spacing (centers), Staggered (most common) or Straight, and Percent Open.
Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.




Element
Element panel sizes are determined by architectural drawings.  Please include any specific instructions in the comment box below.



Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.


FW Series





Please define the pattern with Hole Size, Spacing (centers), Staggered (most common) or Straight, and Percent Open.
Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.






Latitude





Please define the pattern with Hole Size, Spacing (centers), Staggered (most common) or Straight, and Percent Open.
Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.







Legacy




Maximum dimensions are 24" x 96".  Best matl efficiency at 21.5" wide.

Maximum square dimensions are 24" x 24".  Best matl efficiency at 21.5" wide.

For square panel turned 45 degrees, use "Square" Panel Shape. Area of one diamond = 1/2 x B x H

Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.





PermWall 1.0




Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.




R-Panel




Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.




SP 120



Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.



RainScreen Options




If "Other", note in comments section below.


Coping
Sloped Coping
Sloped Coping
Peaked Coping
Peaked Coping
Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.







Fascia
Fascia - Standard
Fascia Standard
Fascia - with Vee
Fascia with Vee
Fascia - Extender
Fascia Extender
Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.







Gutter
A-Style
A-Style
D-Style
D-Style
Downspout
Downspout
Round Gutter
Internal Gutter
Please detail in comments and provide drawing separately if possible

Material Selection
Please refer to the IMETCO Material Availability Chart.  Minimum quantities and extended lead times apply to some selections.







Custom Products
If you need a custom modification to an IMETCO panel, please select that panel in Product Selection and explain the customization in that panel's comment field.

Documents
The following documents are required to begin shop drawings:
- Valid Quote
- Architectural Drawings
- Specifications
- Signed Purchase Order
Tax Exemption Certificate (if applicable)

Total size of attachments can not exceed 20MB. Please email large files to CS@imetco.com or provide link to cloud drive (Google, Dropbox, etc)


If file exceeds 20MB please email to quotes@imetco.com.

If file exceeds 20MB please email to quotes@imetco.com.

If file exceeds 20MB please email to quotes@imetco.com.

If file exceeds 20MB please email to quotes@imetco.com.
Paint Color
Name to be shown on Shop Drawings, "TBD" if unknown

Resources

Search
Generic filters
Exact matches only